Hobart · Dishwasher
Hobart Dishwasher Repair in Washington, DC
House calls for Hobart dishwashers across Washington, DC. The technician tests it, names the failed part and gives you one price before starting.
Open 24/7 · a person picks up
Brands We Repair
From the Prep Line to the Back Bar
Hobart dishwasher repair in Washington, DC: drain faults, film and spots and leaks. Diagnosed on site, one price first.
How a Hobart Dishwasher Repair Visit Works
How Hobart Builds Its Dishwashers
A Hobart dishwasher is really a plumbing appliance with electronics attached: water in, water heated, water sprayed, water out. Most faults sit in that water path rather than in the controls. Hobart equipment is built for foodservice duty, and parts are matched by model and serial number from the data plate. The brand is part of ITW Food Equipment Group. Hobart commercial dishwashers that sanitize with hot water rely on a booster heater, and final-rinse temperature is the first thing an inspector checks.
Hobart Dishwasher Faults We Repair
Several parts can produce the same complaint, so we test before we quote.
- FH / Water Inlet Error (Whirlpool/KitchenAid)
- Leak Detection System Tripped
- Air Gap Clogged
- Garbage Disposal Connection Problem
- Hard Food Disposer Failed
- Starting Intermittently
Other Dishwasher Brands We Repair
What to know about Hobart dishwasher service
Hobart dishwasher repair across Washington, DC, in 18 neighborhoods. Most Hobart dishwasher repairs run $120–$380 and take about 1–2 hours on site.
One thing worth knowing about Hobart: low-temperature Hobart models sanitize with chemicals instead of heat, so a chemical pump or supply-line problem matters as much as any mechanical fault.
Our dishwasher diagnosis follows a sequence: installation details such as the drain loop, air gap and supply valve before internal parts, since a badly routed drain hose causes symptoms that look like a failed pump. It is the cheapest route to the right answer.
What sets the Hobart dishwasher apart
A Hobart dishwasher is really a plumbing appliance with electronics attached: water in, water heated, water sprayed, water out. Most faults sit in that water path rather than in the controls. Hobart equipment is built for foodservice duty, and parts are matched by model and serial number from the data plate. The brand is part of ITW Food Equipment Group. Hobart commercial dishwashers that sanitize with hot water rely on a booster heater, and final-rinse temperature is the first thing an inspector checks.
Beyond that, Hobart builds commercial dishwashers, from undercounter units to door-type and conveyor machines, along with mixers and slicers for professional kitchens.
Common Hobart dishwasher faults
Our starting list for a Hobart dishwasher: leak-protection shutdowns from water in the base; clogged filters and blocked spray arm jets; drain pump jams and air gap blockages; inlet valve faults and short fills; door latch, spring and gasket wear. It reflects how this particular platform tends to fail.
Several of these share symptoms, so the order of testing matters. Starting with the inexpensive possibilities keeps a Hobart dishwasher repair from costing more than it should.
Hobart versus other dishwashers we repair
On Hobart dishwashers the list starts with leak-protection shutdowns from water in the base. That is not true of every maker, which is why the brand matters when you book.
On Admiral dishwashers, the faults we find most often are inlet valve faults and short fills and clogged filters and blocked spray arm jets.
On ASKO dishwashers, the faults we find most often are heater and thermistor faults affecting wash and drying and hardness settings left at default, causing film.
Local conditions and your Hobart dishwasher
Dishwasher calls in DC often involve kitchens renovated inside older rowhouses, where the dishwasher may share a drain with a sink and disposal on plumbing that was never planned for it.
What to have ready when you call about your Hobart dishwasher
Before you call (703) 468-4416, it helps to note when the problem started, whether it is constant or comes and goes, and any code on the display. Those details often point straight at the cause on a Hobart dishwasher.
If your building has rules for contractors, tell us when you call; we can send proof of insurance and plan around the service elevator. Once the technician has found the fault on your Hobart dishwasher, you get one price, and the work carries our 90-day parts and 30-day labor warranty.
Hobart dishwasher repair in numbers
Hobart Dishwasher Questions
Want to talk it through?
Describe the symptom and your neighborhood, and we will tell you when a technician can get there.
Leak-protection shutdowns from water in the base heads the list, followed by clogged filters and blocked spray arm jets and drain pump jams and air gap blockages. Hobart commercial dishwashers that sanitize with hot water rely on a booster heater, and final-rinse temperature is the first thing an inspector checks.
Most repairs fall in the $120–$380 range. A switch, valve, pump or element sits at the low end; a control board or sealed-system repair sits at the top. You get the exact figure after diagnosis and before work starts.
Hobart equipment is built for foodservice duty, and parts are matched by model and serial number from the data plate. The brand is part of ITW Food Equipment Group. Common parts can often come on the first visit if you give us the model number when you book; anything less common is ordered, with the lead time given at diagnosis. Parts are manufacturer-specified by default.